DIY Herringbone Bench
I couldn’t settle for just anything when I designed our DIY herringbone bench.
When I look around our home, I feel settled.
Wrapped up in the comfort of the atmosphere we’ve created. Our hands and hearts have crafted most everything we see here.
You can do it!
Shopping List:
NOTE: Measure your space to make sure that these cuts would fit in your home. Also measure how tall you might want your bench to be as this will change the height of your legs. Don’t forget to take into consideration how wide your bench will be once you secure the short ends to the outside of the legs. This adds space to the width of your bench.
-1 8 ft. 4×4 cut into four 18.5 inch long legs
-2 8ft. 1x4s cut both to be 64 inches. Use the leftover wood to cut 2 boards to 16 inches. This will make up your 4 trim boards that go on the front and the sides.
-1 8ft. 2×4 cut into two 16 inch boards.
-1/4 inch plywood cut to 16×62.5
-180 sq. ft. of wood (of your choice) for the top. The antique flooring we used were 3 inches wide and 3/4 inches thick.
–1.5 Inch nails
Tools List:
–Circular Saw
-Pencil
-Paint, stain, or mineral oil
-Paint or stain for your legs
–Clear Coat
Step 1: Cuts
-Cut wood according to directions above. You can have your lumber cut at the home improvement store and leave with 10 of your cuts already made. We just cut everything at home, but if you’re up for it, this is an option.
Step 2: Legs and Plywood
-Lay plywood on the ground.
-Put wood glue on the top end of each of the four 4×4 legs.
-Glue each leg flush with the outside four corners of the plywood.
-Let them dry then flip it over so the table is standing on its legs..
-Measure 4 inches by 4 inches of each corner on the top of the plywood and draw the square to give yourself a template of where to put your screws.
-Use the drill to put four screws into each corner of the square you drew to securely attach the legs to the plywood.
See below for an example of how they look when they’re nailed flush against each other and into the leg:
Step 3: Side or Top
**You have two options for step 3**
OPTION 1: Saw cuts of herringbone side cuts show (our choice)
OPTION 2: Hide herringbone side cuts
If you chose option 1 do step 3. If you choose option 2, skip to Step 4.
-Nail the 16 inch board to the side of the legs and plywood.
-Repeat with the 64 inch boards to make the front and the back, this time making them flush with the plywood and the 16 inch boards/ends.
-Flip the bench back onto its top and screw in the two 16 inch 2x4s to the front and back (64 inch sides) for added support. We just eyeballed two good, midway support areas.
-Paint or stain your legs and sides at this point if you’re not planning on painting the herringbone. We did this to make sure we wouldn’t accidentally paint that beautiful antique wood!
Step 4: Herringbone
-Once the legs are dry from step 3, flip it back so the bench is standing on its legs.
-Measure the direct middle of your plywood, and draw a line using a board to be your straight edge. You now have a horizontal line running from left to right if you’re looking at the front 64 inch side.
Get the Right View
-Stand at the short side with the line going out directly in front of you. This way, you can watch your herringbone pattern as you create it to make sure it looks right.
For example, when I was standing in that spot upon its completion, it looked like this. See how you get a better look at the pattern from this angle?
-Lay the speed square against the longest side (front 64 inch side) of the plywood to give you a 45 degree angle in order to make your herringbone pattern.
You’re Doing Great!
-Now that the speed square is laying on top of the plywood, take your first board chosen to be a part of your herringbone pattern (in our case, the antique hardwoods) and lay the long side up against the 45 degree angle on the speed square. Make sure to move the board down your speed square until the middle of the board lines up with your center line.**Your wood will be laying awkwardly out to the right of you and not away from you following the line you drew. Remember, you are only working with the right side of the line you drew at the beginning of step 4 right now.**
NOTE: You will want to check and see if your board will need to be cut where it’s laying. If so, scoot it up until you know you can get a full board.
-From underneath the board, run your pencil along the edge of the bench making your cut mark on the wood (in our case, on the antique flooring we’ll use to be the pattern on top).
-Use circular (or miter, whichever you chose) saw to cut on the line.
It’s Coming Together!
-Put glue on bottom of the cut wood. Still standing at the top of the bench with the middle line going straight out from you, line the short end of your cut wood up with the front (64 inch) side of the bench. Place your first herringbone piece with the glue once you see and feel the edges are flush.
-Use the nail gun to shoot one nail into the top of the wood at each corner .
-Take the next board and line up the edge against the nailed down board. The two boards flush against each other should make one long line. This time, you’ll be going out to the left or back side of the bench. Continue marking the bottoms, cutting, gluing, and nailing– alternating from the right side to the left– until you are done with all of your pieces, and your herringbone pattern is complete.
NOTE:
You’ll need to go back in and cut the smaller pieces to finish out the top of your herringbone pattern since we didn’t start at the very top of the bench. You may have to draw lines on both edges to get the right cut.
If you chose OPTION 2 in Step 3, go back to Step 3 now.
Step 5: Sanding
-Use a random orbital sander to smooth the top and sides of the herringbone pattern to make sure you have a clean finish. *TIP: You may want to round the top edges a bit, so sitting is a little more comfy.
Step 6: Finishing
-Paint, stain, or oil your top, sides, and legs.
-Once the top is dry, seal with the clear coat.
-Let dry. Apply second coat if needed and let dry again.
Put in your entry and enjoy!
–